Dowsing Wands

Replacement antenna with clog for Just Flow adjustable dowsing wand. The clog is about 3 cm long and it weighs 1,6 g. The antenna can be replace by loosening the screw with a mini screwdriver. The material of the clog is beech and it is finished with a water-based varnish. The metal is zinc-coated steel. Total length approx. 27 cm.
The head of this antenna is slightly lighter than the ring. For comparison: the ring weighs about 2,5 g and the ball antenna head weighs about 3 g.

A professionally made dowsing wand with a ring or ball. Its beech handle is finished with wax and the wire is galvanised.

The dowsing wand is approx. 45 cm long. The antenna is adjustable. It is possible to lengthen the wire about a 1 cm, to swap the wire for a different one, or shorten it with a pair of pincers if you prefer a shorter antenna.


This dowsing wand comes with a cardboard storage tube (5x55 cm).

A general application hint for dowsing wands is to make sure its movements do not become too wide. Although the wire is flexible, it can endure only so much. Think of it as a spoon that you try to bend repeatedly. The spoon can only endure a certain amount of bends before it will break. Therefore, the size of the movements of the dowsing wand preferably should be at most 1 cm. The more you work with the dowsing wand, the quicker it will react and the wider its movements will be. You can prevent the big movements by learning the command 'slower', which will improve the lifespan of the wire. This applies to every single dowsing wand, as they all have a wire.

A professionally made dowsing wand with a ring. Its beech handle is finished with wax and the wire is galvanised.

The dowsing wand is 45,5 cm long and has an amethyst core in the handle, which protects the user against fatique while working with the dowsing wand and is therefore suitable for sensitive users.


Furthermore, the wire is adjustable. It is possible to lengthen the wire about a 1 cm, to swap the wire for a different one, or shorten it with a pair of pincers.


The dowsing wand comes with a cardboard storage tube.

A general application hint for dowsing wands is to make sure its movements do not become too big. Although the wire is flexible, it can endure only so much. Think of it as a spoon that you try to bend repeatedly. The spoon can only endure a certain amount of bends before it will break. Therefore, the size of the movements of the dowsing wand should be at most 1 cm. The more you work with the dowsing wand, the quicker it will react and the bigger its movements will be. You can prevent the big movements by learning the command 'slower', which will improve the lifespan of the wire. This applies to every single dowsing wand, as they all have a wire.

This dowsing wand has a fixed wire with ring and its handle contains a small vial with a physiological saline solution. This salt solution assists in energetic protection when working with the dowsing wand. The size of the tube is approximately 4.8 x 1 cm and can be removed to replace of refill.



The total length of the dowsing wand is approximately 44.5 cm. The ring has a cross section of 3.5 and the size of the handle is 13 x 1.9, excluding the vial. Its beech handle and ring are finished with wax.



The total length of the wire, including its ring, is approximately 30 cm and it is fixed in the handle. The length of the wire causes the dowsing wand to react flexibly, but it does need a little more time to change its direction.



This dowsing wand is delivered in a white, cardboard storage tube.

Dowsing wand does not have a normal wire. Its wire is a thick spring with a small ball at the end. Because of this, the dowsing wand is more flexible and can handle bigger movements. This type of dowsing wand is often used for aura / chakra dowsing work.



Its total length is approximately 30 cm. The orb has a diameter of 22 mm, the handle is approximately 10 cm long.



The ball is quite heavy and because of this, the dowsing wand bends downwards when you hold it, which makes it probably a bit harder for beginners to move it, so you would need a little extra patience in that case.

This dowsing wand comes in a storage box made from cardboard covered with red paper. The boxes used to be in a plastic bag, but as of late, they have done away with that and stuck the label from the wholesaler straight onto the box, and removing it damages the paper a bit. A photo of this is included so you can determine whether or not this is a deal breaker for you. 

A small, straight screwdriver for adjusting the antenna of the adustable dowsing wand Just Flow. The screwdriver is 4,5 cm long, the handle has a diameter of 6 mm and the blade (the part you put on the screw) is 2 mm wide.

Replacement part for the travel dowsing wand. This is the bottom part of the antenna, the part that goes into the handle.

A replacement wire with ball for adjustable dowsing wand Just Flow. The ball has a diameter of 20 mm. The wire is easily changed by unscrewing the small screw in the brass holder at the top of the handle.

The beech ballis finished with a clear varnish and the wire is galvanised. The wire is 26 cm long and the orb weights approximately 3 g. It is a little heavier than the wire with a ring, which weights approximately 2.5 g.

A replacement wire with wooden ball for adjustable dowsing wand 7. The ball is finished with wax and the wire is galvanised. The wire is 36cm long and this combination is a little heavier than the wire with ring. This wire is also suitable for the adjustable dowsing wand Just Flow 5. In that case, the wire will need to be shortened for a better fit.